HP SmartCard NIPRNet Solution for US Government Manuale Utente

HP SmartCard SIPRNet and NIPRNetSolutions for US Governmentusing HP FutureSmart rmwareAdministrator’s Guide

Verify the network settingsUse the following information to verify the HP printer’s TCP/IP network information.1. Open the EWS.For instructions, see A

Congure the sign-in method to enable SmartCard authenticationUse the Access Control page of the EWS to set up the Smart Card or the SIPRNet Smart Car

5. In the Enable and Congure Sign-in-Methods section, select Setup in the Status column where the Sign in method column is either the Smart Card entr

7. After the page refreshes, review the Enable and Congure Sign In Methods section of the Access Control panel to verify that the Status for the Smar

10. Click Apply to save the changes.Figure 3-6 Smart Card option in the Sign In and Permission Policies10 Chapter 3 Congure the printer settings u

Congure certicate managementSet up security certicates on the Certicate Management page of the EWS:1. Open the EWS.For instructions, see Access th

7. If OCSP is used for certicate revocation checking, complete the following steps:a. Click the Certicate Validation tab.b. Select the Perform OCSP

a. Select the Retrieve base CRL every time check box (the default) to retrieve the list every time.-or-Select the Enable base CRL caching check box to

Congure the Scan/Digital Send settingsUse the Scan/Digital Send tab of the EWS to congure the address book, e-mail, and network folder settings.●Add

c. In the Server Authentication Requirements section, select the Server requires authentication radio button, and then select Use credentials of user

Copyright and License© Copyright HP Development Company, L.P.Reproduction, adaptation, or translation without prior written permission is prohibited,

a. Select the Enable Send to E-mail check box.b. In the Outgoing E-mail Servers (SMTP) section, click Add to start the wizard.Figure 3-12 E-mail Setu

d. On the Server Usage section, select which functions the server is used for, and then click Next.e. Review the Summary and Test page.To test the set

d. Select to clear the Use the recipient public key certicate to verify the recipient check box.Figure 3-15 Signing and Encryption7. Click the Apply

5. In the Quick Sets section, click Add to start the wizard.Figure 3-17 Quick Set Wizard6. In the Quick Set Wizard, complete the following tasks to d

ii. In the Retrieve the device user's home folder using this attribute eld, type homeDirectory, and then click Next.Figure 3-18 Folder settings

4 Device ResetsThis chapter provides instructions to restore the HP printer to factory defaults.●Restore Factory defaults●Preboot MenuRestore Factory

Figure 4-2 General SettingsFigure 4-3 Restore Factory Settings2. In Restore Factory Settings, select Restore or Cancel .NOTE: Access code might be r

●Date and Time ( Time Zone)●Network Settings ( IP, DNS)●Certicates●Control Panel CustomizationDrag icons o the homescreen that are not used and plac

Preboot MenuThis section provides instructions on how to perform a Partial Clean using the printer’s control panel when an error message displays on t

4. Depending on your printer, perform one of the following tasks:Use the touch screen scrollbar or touch the down arrow to select Partial Clean, tou

Table of contents1 Introduction ...

A LicensesThis solution from HP uses and contains open source code and libraries from Heimdal Kerberos 5, OpenLDAP, OpenSC, and OpenSSL. Following are

Heimdal KerberosThis product contains Heimdal Kerberos in binary form. Use of this software is governed by the terms of the license below:Copyright ©

OpenLDAPThis product contains OpenLDAP in binary form. Use of this software is governed by the terms of the license below:The OpenLDAP Public LicenseV

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.2. Redistributions in b

OpenSCOpenSC CreditsOpenSC was written by (or uses code copied from):●Alon Bar-Lev●Andrea Frigido●Andreas Jellinghaus●Antonino Iacono●Antti Partanen●A

●Marc Bevand●Marie Fischer●Markus Friedl●Martin Paljak●Mathias Brossard●Matthias Brüstle●Nils Larsch●Olaf Kirch●Peter Koch●Priit Randla●Robert Bihlmey

OpenSC does not include the ocial PKCS#11 header le, because that le is under a non-free license. Instead OpenSC contains a rewritten header le fr

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.2. Redistributions in b

OpenSSLThis product contains OpenSSL in binary form. Use of this software is governed by the terms of the license below:Copyright © 1998-2003 The Open

Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Y

Appendix B Warranty Service ...

SHA-2This product may include the following software in binary form: SHA‐2 implementation by Olivier Gay. Use of this software is governed under terms

B Warranty ServiceHP Limited Warranty StatementHP Product Duration of Limited WarrantyHP SmartCard NIPRNet Solution for US Government and the HP Smart

7. HP’s limited warranty is valid in any country/region or locality where HP has a support presence for this product and where HP has marketed this pr

1 IntroductionThe HP SmartCard NIPRNet Solution for US Government and the HP SmartCard SIPRNet Solution for US Government are designed to optimize sec

2 Getting started with HP SmartCard SIPRNet or NIPRNet SolutionGet started by installing the HP SmartCard SIPRNet or NIPRNet Solution on HP products w

Figure 2-2 HP SmartCard SIPRNet SolutionObtain tools for conguring the printerThe Tools directory in the HP CAC website provides the les required f

3 Congure the printer settings using the Embedded Web ServerAfter installing the HP SmartCard NIPRNet or SIPRNet Solution on the printer, open the HP

Set the date and timeThe device date and time must be synchronized to within ve minutes of the date and time on the Kerberos server. If the time die