HP rp7410 Guida Utente Pagina 120
- Pagina / 266
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
HP OpenVMS I64 Support for Cell Local Memory
On servers based on the HP sx1000 chipset or HP sx2000 chipset, each cell has a cell local memory
(CLM) parameter, which determines how firmware interleaves memory residing on the cell.
NOTE: HP OpenVMS I64 does not support using CLM. Before booting OpenVMS on an
nPartition, you must ensure that the CLM parameter for each cell in the nPartition is set to zero
(0). Although you might be able to boot OpenVMS on an nPartition with CLM configured, any
memory configured as cell local is unusable, and such a configuration is untested and
unsupported.
To check CLM configuration details from an OS, use Partition Manager or the parstatus
command. For example, the parstatus -V -c# command and parstatus -V -p# command
report the CLM amount requested and CLM amount allocated for the specified cell (-c#, where
# is the cell number) or the specified nPartition (-p#, where # is the nPartition number).
To check CLM configuration details from the EFI Shell on a cell-based HP Integrity server, use
the info mem command. If the amount of "NonInterleaved Memory" reported is less than 512
MB then no CLM is configured for any cells in the nPartition (and the indicated amount of
noninterleaved memory is used by system firmware). If the info mem command reports more
than 512 MB of noninterleaved memory then use use Partition Manager or the parstatus
command to confirm the CLM configuration details.
To set the CLM configuration, use Partition Manager or the parmodify command.
Adding HP OpenVMS to the Boot Options List
On HP Integrity servers, you can use the following procedures to manage boot options list entries
for HP OpenVMS.
You can add the \efi\vms\vms_loader.efi loader to the boot options list from the EFI Shell
or EFI Boot Configuration menu (or in some versions of EFI, the Boot Option Maintenance
menu).
NOTE: OpenVMS I64 installation and upgrade procedures assist you in setting up and validating
a boot option for your system disk. HP recommends that you allow the procedure to do this.
To configure booting on Fibre Channel devices, you must use the OpenVMS I64 Boot Manager
utility (BOOT_OPTIONS.COM). For more information on this utility and other restrictions, refer
to the HP OpenVMS for Integrity Servers Upgrade and Installation Manual.
Procedure 5-15 Adding an HP OpenVMS Boot Option
This procedure adds an HP OpenVMS item to the boot options list from the EFI Shell.
To add an HP OpenVMS boot option when logged in to OpenVMS use the
@SYS$MANAGER:BOOT_OPTIONS.COM command.
1. Access the EFI Shell environment.
Log in to the management processor and enter CO to access the system console.
When accessing the console, confirm that you are at the EFI Boot Manager menu (the main
EFI menu). If at another EFI menu, select the Exit option from the sub-menus until you
return to the screen with the EFI Boot Manager heading.
From the EFI Boot Manager menu, select the EFI Shell menu option to access the EFI Shell
environment.
120 Booting and Resetting nPartitions
- Published: February 2009 1
- Edition: Second Edition 1
- Table of Contents 3
- 4 Table of Contents 4
- Table of Contents 5 5
- 6 Table of Contents 6
- Table of Contents 7 7
- List of Figures 8
- List of Tables 9
- List of Examples 10
- About This Document 11
- Typographic Conventions 12
- Related Information 13
- Publishing History 13
- HP Encourages Your Comments 13
- Introduction to nPartitions 15
- Partition Manager 22
- Partition Numbers 24
- Assigned and Unassigned Cells 24
- Base Cells 24
- Core Cells 24
- Active and Inactive Cells 25
- Cell Local Memory 25
- Cell Property Details 25
- Basics of nPartition Creation 29
- Genesis Partition 30
- Complex Profile 36
- Complex Profile 37 37
- Complex Profile Group Details 39
- IPMI Block Transfer (IPMI BT) 42
- IPMI over LAN 42
- Local Management 43
- Remote Management Using WBEM 44
- Superdome Server Models 57
- 3 Planning nPartitions 61
- 64 Planning nPartitions 64
- Using Service Processor Menus 76
- Viewing Console Logs 77
- Tools for Booting nPartitions 95
- for a root device and 96
- Troubleshooting Boot Problems 100
- [Bumped user - Admin.] 104
- Finding Bootable Devices 106
- GSP:CM> TC 107
- Booting HP-UX 110
- fs1:, and so on 113
- Shutting Down HP-UX 117
- Shutting Down HP OpenVMS 123
- Booting Microsoft Windows 126
- you can initiate the 132
- Shutting Down Linux 134
- Booting over a Network 147
- Using HP-UX Loader Commands 151
- Linux Boot Option Management 153
- ELILO boot: Tab 154
- ELILO boot: linux-up 154
- Uncompressing Linux... done 155
- ELILO boot: linux S 155
- Configuring Autoboot Options 158
- Shell> boottest -h 162
- Shell> 162
- Creating a Genesis Partition 170
- Creating a New nPartition 172
- # parmodify -p0 -d2 184
- Command succeeded 184
- Renaming an nPartition 185
- Renaming a Server Complex 187
- Setting Cell Attributes 189
- Setting Cell Attributes 191 191
- Setting Cell Attributes 193 193
- # parmodify -p0 -r2 -r0 197
- 7 Managing Hardware Resources 201
- Processors 218
- Tools for Listing Status 223
- Listing Cell Configurations 226
- Listing Memory Configurations 229
- Listing Fan and Blower Status 240
- 3. Exit Partition Manager 241
- A nPartition Commands 243
- I/O Specification Format 244
- 246 nPartition Commands 246
- 248 nPartition Commands 248
- Synopsis 249
- 250 nPartition Commands 250
- 254 nPartition Commands 254
- -h IPaddress 257
- 264 nPartition Commands 264
Prodotti e manuali riguardandi Software HP rp7410
Software HP 11i Manuale Utente
(113 pagine)
(113 pagine)
Software HP 41B Manuale Utente
(44 pagine)
(44 pagine)
Software HP P6350 Manuale Utente
(316 pagine)
(316 pagine)
Software HP CD52ce Manuale Utente
(109 pagine)
(109 pagine)
Software HP STORAGEWORKS XP20000 Manuale Utente
(76 pagine)
(76 pagine)
Software HP -UX SNAplus2 Manuale Utente
(398 pagine)
(398 pagine)
Software HP D2D2502i Manuale Utente
(178 pagine)
(178 pagine)
Software HP Firewall Series Manuale Utente
(119 pagine)
(119 pagine)
Software HP tc4400 Guida Utente
(86 pagine)
(86 pagine)
Software HP PROCURVE 2520 Manuale Utente
(544 pagine)
(544 pagine)
Software HP 1.x Carta bianca
(16 pagine)
(16 pagine)
Software HP B6960-90078 Manuale Utente
(856 pagine)
(856 pagine)
Software HP 2600-PWR Manuale Utente
(418 pagine)
(418 pagine)
Software HP 5992-3193 Manuale Utente
(66 pagine)
(66 pagine)
Software HP Laptop 7.2 Manuale Utente
(53 pagine)
(53 pagine)
Software HP 1.5TB Manuale Utente
(216 pagine)
(216 pagine)
CDA CI330 manuali
Manuali dei proprietari e guide per l'utente per Lavatrici CDA CI330.
We fornisce 1 manuali pdf CDA CI330 per scaricare gratuitamente in base al tipo di documento: Specifiche
Commenti su questo manuale