HP Server rp7400 Manuale Utente

1Adding a Disk DriveThe internal disk drives (A upper and B lower) are located in the back of the SPU. The internal disk drives are hot swapable whe

10

11Upgrading Secure Web Console FirmwareThe following paragraphs describe the procedures to upgrade your Secure Web Console (SWC) firmware.Secure Web

12NOTE The path above is for demonstration only. The XX.X at the end of the example will be filled with the upgrade version you are installing.Step 4.

13CAUTION Permanent damage to the product may result if these instructions are not followed EXACTLY.CAUTION The transfer must be done in Binary mode

14Step 8. Using FTP, transfer these files to an empty directory on your local FTP server. Ensure that the file and directory permissions are set so th

15Add-On MemoryFollow these procedures to add memory to an rp7400 server.Memory Configuration RulesAn rp7400 system supports up to 4 memory carriers

16Procedure Overview1. Remove power from the system.2. Remove the front bezel.3. Extend the SPU out the back of the cabinet.4. Remove the back top cov

17Step 1. Remove Power From the SystemCAUTION Before starting any shut down type procedures, be sure to check with the System Administrator or custo

18b. Carefully extend the SPU out the front of the cabinet approximately 2 to 4 inches.c. Loosen the six (three on each side) mounting screws holding

19NOTE It is recommended that you pull the SPU from the back of the cabinet. This allows you to monitor the cable movement to avoid snags and tangle

2Once you have completed the addition of the disk drive, you must perform the Hot swap procedure:Hot Swap Software ProcedureNOTE HP often uses differe

20susceptible to EMI problems. To remove the back air baffle from the:a. Loosen the two captive mounting screws at the support bridge.b. Grasp the air

21DIMM) press the memory DIMM into the memory carrier slot until the memory DIMM fully seats and the extractor levers are up against the outside edg

22EMI problems. To replace the back air baffle in the SPU:a. Angle the back edge of the air baffle onto the support bridge flange, then lower the air

23the front of the SPU sticks out approximately 2 to 4 inches.NOTE It is recommended that you push the SPU from the back of the cabinet. This allows

24Step 12. Replace the Front BezelTo replace the front bezel, perform the following steps:a. Align the front bezel over the front of the SPU.b. Press

25indications.e. Check all front panel LEDs for normal indications, with no warnings ar faults indicated.The SPU should take a few minutes to perfor

26

27Add I/O CardsThe rp7400 server has 12 expansion I/O slots accessible through side panels on the rear of the SPU chassis. Six slots are located on e

28Step 1. Remove Power from the System.CAUTION Before starting any shut down type procedures, be sure to check with the System Administrator or custom

29WARNING Only extend one SPU at a time. Never attempt to extend more that one SPU for any reason.Step 4. Remove the PCI Cover PlateNOTE Steps 4 thro

3lvcreate -C y -r n root /dev/vgroot Step 9. Extend the mirrors onto the disk you’ve added. For example:lvextend -m 1 <LV name> /dev/vgroot/ro

30e. Insert the four (two on each side, T25) SPU retainer screws, located just below and above bezel snap tabs.Check all cables to be sure none have b

31I/O Scan-to-Slot MatrixSlot Number Hardware Path Slot Type1 0/5/0 2xPCI2 0/5/0 2xPCI3 0/4/0 4xPCI4 0/8/0 4xPCI50/10/04xPCI6 0/2/0 4xPCI71/12/04xPCI

4Step 2. Create a physical volume using pvcreate with the -B option. -B creates an area on the disk for a LIF volume, boot utilities, and a BDRA (Boot

5lvextend -m 1 <LV name> /dev/vgroot/root /dev/dsk/cXtXdX Step 12. Synchronize the mirrors. This may take several minutes as it will have to c

6

7Adding a Power SupplyBefore unpacking the new power supply, inspect the shipping carton for obvious damage. If damage to the shipping carton is obs

87. Push the power supply into the SPU firmly until the insertion/extractor lever can hook under the extended tab on the SPU.8. Push the insertion/ext

9of the chassis.Once the system is re-assembled, be sure there are no errors on the front panel or system console. Be sure the system is ready for c