HP AP5000 Guida di Avvio Rapido

HP Linear ScannerQuick Reference Guide

Figure 2-2 Trigger Single ModeTrigger Hold Multiple ModeWhen the trigger is pulled, scanning starts and the product scans until the trigger is releas

Figure 2-5 Flashing ModeAlways OnNo trigger pull is required to read a barcode. Scanning is continually on. If the trigger is pulled, thereader acts

Programming BarcodesFor your convenience, this guide includes the programming barcodes required to configure thescanner for use with different interfa

LED and Beeper IndicationsThe scanner’s beeper sounds and its LED illuminates to indicate various functions or errors on thereader. A “Green Spot” als

A TroubleshootingSolving Common ProblemsThe following table lists possible problems, causes, and recommended solutions.Problem Possible Cause Possible

●Error messages received● Hardware configuration●Hardware and software you are usingENWW Preparing to Call Technical Support 9

B Agency Regulatory NoticesFederal Communications Commission NoticeThis equipment has been tested and found to comply with the limits for a Class B di

For questions regarding this FCC declaration, contact:Hewlett Packard CompanyP. O. Box 692000, Mail Stop 510101Houston, Texas 77269-2000Or, call (281)

Japanese NoticeKorean NoticeProduct Environmental NoticesMaterials DisposalSome HP LCD monitors contain mercury in the fluorescent lamps that might re

Disposal of Waste Equipment by Users in Private Household in theEuropean UnionThis symbol on the product or on its packaging indicates that this produ

© 2011 Hewlett-Packard DevelopmentCompany, L.P.Microsoft, Windows, and Windows Vista areeither trademarks or registered trademarksof Microsoft Corpora

ᴹ∂ᴹᇣ⢙䍘઼ݳ㍐৺ަਜ਼䟿㺘ṩᦞѝഭⲴlj⭥ᆀؑ᚟ӗ૱⊑ḃ᧗ࡦ㇑⨶࣎⌅NJ޻ᆎᶗI/O PCAsཌ䜞᧝࡬䇴༽⭫㔼⭫Ⓠ䭤ⴎ啖ḽᵰ㇧ެԌ伄᡽޻䜞ཌ䜞჈։䰻䈱䇴༽ѱᶵ༺⨼ಞૂᮙ✣ಞ⺢ⴎ傧ࣞಞᱴ⽰ኅO: 㺞⽰䈛ᴿ∈ᴿᇩ⢟䍞൞䈛䜞Ԭᡶᴿൽ䍞ᶆᯏѣⲺ੡䠅ൽ൞SJ/T11363-2006ḽ߼㿺ᇐⲺ䲆䠅㾷≸ԛс

About This GuideThis guide provides information on setting up and using the HP Linear Scanner.WARNING! Text set off in this manner indicates that fail

iv About This Guide ENWW

Table of contents1 Setting Up the Scanner ...

Chemical Substances ... 13Restriction of Hazardou

1 Setting Up the ScannerFollow the steps below to set up the scanner.1. Connect the interface cable to the bottom of the scanner.Figure 1-1 Connectin

4. Ensure that the scan line crosses every bar and space of the barcode.Figure 1-4 Correct and Incorrect Scans5. Do not hold the scanner directly ove

2 Using the ScannerParts of the ScannerFigure 2-1 Scanner Parts(1) LED(2) Scan Window(3) Nose Boot(4) TriggerScanning ModesThe scanner can operate in